How do I configure a Lucent Multiband IMUX using the 960/970?

Connect the Lucent Multiband IMUX to the 960/970 COM 1 port using the Db9 Female end of the Db9 to RJ12 cable Ascend Part#: 2510-0088-001, PACT Part#: 180-0184-01)) and connect the RJ12 end to the Control port of the IMAX. With the 960/970 Collaboration Application closed, open the Microsoft HyperTerminal terminal emulation program: START >> PROGRAMS >> ACCESSORIES >> HYPERTERMINAL
Launch HyperTerminal: Connection Description > Name: (anything can be typed in here) then click OK.
Connect To > Connect Using: COM 1 then click OK.
COM1 Properties/Port Settings: Bits per second: 9600
Data Bits: 8
Parity: NONE
Stop Bits: 1
Flow Control: NONE Click OK.
Press Ctrl / L on your keyboard to refresh the screen. At this point you will be in control of the IMUX. The IMUX has four different menus(Configure, Directory, Diagnostics, Security). To see all the menus go to the Main Edit Menu by pressing the Esc key on your keyboard. To configure the IMUX select the Configure Menu. To do this make sure your arrow (>) is to the left of Configure. Now either use your "right arrow key" or "enter" key on your keyboard to access the Configure screen. You will use the arrow keys, Esc and enter buttons to navigate in the IMUX.
Configure screen: My Name: Type Company Name etc.. Switch Type = (AT&T/P-T-P, AT&T/Multi-P, NTI, NI-1) Get Switch Type info from Local Telephone Carrier. Line 1: Enabled = Yes Chan Usage = Switch/Switch My Num A = B1 from 1st line( 4-7 digit# ) My Num B = B2 from 1st line if AT&T P-T-P no B2) SPID 1 = usually your 7 digit or 10 digit B1 Tel # plus a suffix or prefix (Get SPIDs from your Local Telephone Carrier) SPID 2 = B2 plus a suffix or prefix Note: NO SPIDS for AT&T P-T-P Switch Type. You can have from 1 to 4 ISDN lines and would configure them in this manner. After configuring all lines go back to the Configure screen. The following fields after Line 4 are not configured here ( Dial #, Data Svc, Call Type and Call Mgm). Set Idle = None >>> Dial = RS-366 Ext1>>> Answer = P-Tel Man >>> Clear = DTR Inactive >>> Early CD = None >>> Strip Digit = (Blank)
Advanced ... Go into the Advanced Menu by using your right arrow or enter. Configure Advanced ... Term Rate = 9600 >>> Console = Standard Remote Mgmt = Yes >>> Parallel Dial = 5 >>> Auto Logout = No >>> Idle Logout = 0 >>> RS-366 Esc = N/A >>> Dual Port = 1 & 2 Dual if making 2 channel calls) >>> Dual Port = No Dual(if only making bonded 1 channel calls) >>> Delay Dual = Yes if making 2 channel calls) >>> Delay Dual = No if only making bonded 1 channel calls).
Now the IMUX DIRECTORY must be configured. Go to Main Edit Menu > Arrow down to Directory > Either use your right arrow or enter key to access the Directory Dialing IMUX Codes. The Dialing Codes in the IMUX MUST be the same as the Dialing Codes hard set in the 960/970. The 960/970 default Lucent Multiband IMUX codes are the following: ( See Page 3-11 of the PictureTel 900 Series Collaboration System Administrator's Guide )

Call Profile Code) Name Data Rate
#001 1x56kbps non-bonded, restricted
#002 1x64kbps non-bonded
#003 2x56kbps non-bonded, restricted
#004 2x64kbps non-bonded
#005 1x112 kbps bonded, restricted
#006 1x128 kbps bonded
#007 1x224 kbps bonded, restricted
#008 1x256 kbps bonded
#009 1x336 kbps bonded, restricted
#010 1x384 kbps bonded
#011 1x448 kbps bonded, restricted
#012 1x512 kbps bonded
#013 1x672 kbps bonded, restricted
#014 1x768 kbps bonded

To configure the first Dialing Profile Code) #001 1x56kbps you arrow to "01" in the Directory. Name = 1x56k >>> Dial = Leave blank >>> Call Type = 1 Chnl >>> Call Mgm = N/A >>> Data Svc = 56K >>> Force 56 = No. Leave the remaining fields as they are currently displayed. Now press "Esc" then either arrow down to 2= Exit and Accept and press Enter or simply Press "2". This Dialing Profile Code) is currently stored in your Dialing Directory. The second Dialing Profile Code) #002 1x64kbps will be set up the same as #001 except Name = 1x64k and Data Svc = 64K. To set up Dialing Profiles Codes) #003 & #004, Name each Profile Code) appropriately and set Call Type = 2 Chnl. All other settings remain the same as the first two Profiles Codes).
To set up Profile Code) #005 - #014 do the following: Set Name appropriate per Profile Code) >>> Call Type = BONDING >>> Call Mgm = Mode 1 >>> Data Svc = 64k for all 64k call profiles codes) and 56k for all 56k call profiles codes) >>> Force 56 = No >>> Base Ch Count = 2 for #005 & #006, 4 for #007 & #008, 6 for #009 & #010, 8 for #011 & #012 and 12 for #013 & #014.
You are now ready to make calls.